|
Re: what to do with all those leftover freight car trucks?
rwitt_2000
On Wed, Aug 21, 2019 at 02:15 AM, Tim O'Connor wrote:
Tom Swift has been posting wonderful pictures on Facebook of the CB&Q Havelock shopsQuestion: I assume these side frames are the raw castings. What if any areas and surfaces were machined before they became part of a functioning truck? Bob Witt
|
|
|
|
Re: what to do with all those leftover freight car trucks?
In the paint shed.
Thanks!
From: <main@RealSTMFC.groups.io> on behalf of "Bob Chaparro via Groups.Io" <chiefbobbb@...>
In the photo I see truck frames and car doors. Where are the bottle of MEK?
|
|
|
|
Re: what to do with all those leftover freight car trucks?
In the photo I see truck frames and car doors. Where are the bottle of MEK?
Bob Chaparro Hemet, CA
|
|
|
|
MEK Substitute and current plastic cements
Andy Carlson
Don, I can surmise that your chemist friend has never built styrene single sheathed patterns, at least not with ACC. Years ago Al Armitage recommended MEK for styrene fabrication for multiple reasons. Not lost on me was his mentioning MEK is 100% evaporative--that is, every bit of MEK we use will dissipate away to nothingness. You may wonder why this is important; and it is to prevent sometime reactions of residual solvent with RTV mold material. The gentleman who mentored me on mold making and casting started out with model pattern making using Testors liquid cement and many of his early molds had problems curing completely. This was prevented with the switch to MEK. I have evolved beyond being struck with warpage years ago. Laminating 0.005" styrene plates to a thicker styrene substrate caused lots of warping. That has been solved with a glueing technique I have shared with this group a few times over the years. Regards to everyone! -Andy Carlson Ojai CA
On Wednesday, August 21, 2019, 6:09:33 AM PDT, Donald B. Valentine via Groups.Io <riverman_vt@...> wrote:
OK folks, Bill Aldrich, whom as I mentioned has a doctorate Inorgamic Chemistry, kicked this cement business around for about 45 minutes. For small plastic parts/pieces and such Bill uses ACC for almost everything. For other things he uses acetone and keeps it in a bottle with a cork or rubber stopper to seal it tightly and not lose it from evaporation.......He also uses ACC when joining sheet material and notes that cements that actually dissolve sheet material to join them cause a warpage problem that may not show up for a year or more. This is because even if the sheets being joined are of the same material all too often each sheet with cure at a different rate. Since there is shrinkage involved in the curing a different rate in each sheet will cause warping. Thus he uses the ACC for sheets as well as all small parts. He did note that MEK or trichloroethylene can be used but doesn't particularly recommend them. Hope this information is helpful, Don Valentine
|
|
|
|
Re: what to do with all those leftover freight car trucks?
Richard McQuade
Thanks Tom. Great gondola load. Would never have thought of doing that.
Richard
|
|
|
|
Re: MEK Substitute and current plastic cements
Denny Anspach <danspachmd@...>
After a determined try with seven paint suppliers in this region, this was my result: Five had in hand or would only order MEK substitute. One had MEK in gallons @$49.00. One (Menard’s) had a deep shelf of MEK quarts @$9.50. The 20 miles drive to secure the latter was leavened completely by a nearby stunningly-delicious(!) supper of lengua, onions and cilantro (in Iowa, no less!).
I thank all of those who have divulged the chemical formulations. This kind of information will almost certainly be more and more useful for many in this hobby. I am a big fan of Tamiya products, and I am surely going to try their thin cement. I have a can of their new-to-me semi-gloss clear coating that I am looking to for the many finishes that demand something more than dead flat, but not anywhere near a reflective gloss. Denny Denny S. Anspach MD Okoboji, IA
|
|
|
|
Re: MEK Substitute and current plastic cements
Donald B. Valentine <riverman_vt@...>
OK folks, Bill Aldrich, whom as I mentioned has a doctorate Inorgamic Chemistry, kicked this cement business around for about 45 minutes. For small plastic parts/pieces and such Bill uses ACC for almost everything. For other things he uses acetone and keeps it in a bottle with a cork or rubber stopper to seal it tightly and not lose it from evaporation. Pierre may not like this but Bill does NOT recommend MEK for plexiglass stating that it creates a weak joint at best on all but very small pieces. He also uses ACC when joining sheet material and notes that cements that actually dissolve sheet material to join them cause a warpage problem that may not show up for a year or more. This is because even if the sheets being joined are of the same material all too often each sheet with cure at a different rate. Since there is shrinkage involved in the curing a different rate in each sheet will cause warping. Thus he uses the ACC for sheets as well as all small parts. He did note that MEK or trichloroethylene can be used but doesn't particularly recommend them. Ambroid has been mentioned in several posts in this thread. Is it no longer available? Last I knew some ten years ago a fellow in his mid-30's had purchased the line and moved it to Springfield, VT. I met him at some show or meet and he was offering the standard old Ambroid cement in a tube and several new varieties in bottles. Is none of this available now? Tenax has also been mentioned. In my experience it was never more than worthless. I was never able to join anything with it and gave up with thje first bottle. Hope this informaiton is helpful, Don Valentine
|
|
|
|
Re: SOMETIMES YOU JUST HAVE TO BLINK
Staffan Ehnbom
The GN 72750-72773 series container gondolas was extended to 72774 by the July 1970 ORER at least. Staffan Ehnbom
On Wed, Aug 21, 2019 at 6:54 AM Tim O'Connor <timboconnor@...> wrote:
|
|
|
|
what to do with all those leftover freight car trucks?
Tom Swift has been posting wonderful pictures on Facebook of the CB&Q Havelock shops
in 1948. This one today shows a very interesting MP GS gondola being unloaded and a wide area shot showing lots of interesting freight car stuff. Tim O'Connor -- *Tim O'Connor* *Sterling, Massachusetts*
|
|
|
|
Re: SOMETIMES YOU JUST HAVE TO BLINK
This is what happened to at least one of those Greenville 1321's... :-)
On 8/20/2019 3:22 PM, WILLIAM PARDIE wrote:
--
Tim O'Connor Sterling, Massachusetts
|
|
|
|
Re: SOMETIMES YOU JUST HAVE TO BLINK
Ed, thanks for the additional pictures! I'm especially happy the car is coupled to a Southern Pacific hopper! However you might want to check your number series - 72774 is not part of any of the series you listed. I agree the reinforced ribs are just that, and nothing more. I wish those Sunshine kits were still available! Tim O'Connor
On 8/20/2019 12:00 PM, spsalso via Groups.Io wrote:
Tim, --
Tim O'Connor Sterling, Massachusetts
|
|
|
|
Re: NWSL to continue business
Pierre Oliver
Oh wouldn't that be nice! Pierre Oliver www.elgincarshops.com www.yarmouthmodelworks.com On 8/20/19 6:46 p.m., Tony Thompson
wrote:
It's super good news that NWSL will continue. Maybe they could buy up Reboxx <g>.
|
|
|
|
Re: NWSL to continue business
Tony Thompson
It's super good news that NWSL will continue. Maybe they could buy up Reboxx <g>.
Tony Thompson
|
|
|
|
Re: MEK Substitute and current plastic cements
I use Tamiya Extra Thin when I want quicker results than Testers. otherwise Testers for it slowness, as when I am harvesting and gluing down rivets/bolt heads. I have one of the older squat Testers bottles that I refill while the Tamiya bottle is also squat and thus less prone to getting tipped.
There has been a shortage of the Tamiya product so I bought two bottle at the C'ville RPM and illegally secured one each in my sneakers in my suitcase. Bag was searched but the Tamiya made it through. The Tamiya brush is nice and small and telescopes to reach the bottom when necessary. Bill Welch
|
|
|
|
Re: MEK Substitute and current plastic cements
Denny
toggle quoted messageShow quoted text
Tenax is dichloromethane (aka methylene chloride). I bought a QUART on Amazon. MEK is methylethylketone, or 2-butanone. I have a quart of that too. :-) Tim O' ===========================
On 8/20/2019 9:55 AM, Denny Anspach wrote:
I am on the very edge of using up the last drops of my Tenax and Ambroid liquid plastic cements, and I was jolted this morning when my reliable ACE Hardware store informed me that they can no longer carry my otherwise usual MEK (and this is IOWA, not California). I do have some Testors (2-3 years old), but at least the bottle that I have seems to take forever or…. not at all to set up. --
*Tim O'Connor* *Sterling, Massachusetts*
|
|
|
|
Re: MEK Substitute and current plastic cements
Donald B. Valentine <riverman_vt@...>
Jon Miller wrote: I've never had any luck using MEK to join
Plexiglas. I use a acrylics cement from TAP plastic. The can
says Dichloromethane contains;
Methylene chloride Trichloroethylene Methyl Methacrylate Monomer Anyone know a chemist?: Yes, as a matter of fact. Noted New Haven modeler Bill Aldrich has a doctorate in Inorganic Chemistry and a second one in Metallurgy. Since we speak three or four tims a week I will ask him. Cordially, Don Valentine
|
|
|
|
Re: SOMETIMES YOU JUST HAVE TO BLINK
WILLIAM PARDIE
If anyone is interested here are two of the three “oddballs” on my western railroad. Thanks for all of the responses. Your opinions are all valued. Bill Pardie
|
|
|
|
Re: Paint Damage from Bubble Wrap
Brian No, they don't. I have ordered BUNDLES of boxes and envelopes from the Post Office web site. These come in many sizes and a single bundle is around 25 boxes I think. I ordered them online, and the post office delivered them in a couple of days. NO CHARGE. I do use them to mail stuff (there is postage for that), so I'm not taking advantage. It's just their way of "priming the pump". Tim O'Connor
On 8/20/2019 1:09 AM, BRIAN PAUL EHNI wrote:
When you send the package, they scan the bar code on the envelope or box to charge you. --
Tim O'Connor Sterling, Massachusetts
|
|
|
|
Re: SOMETIMES YOU JUST HAVE TO BLINK
WILLIAM PARDIE
In the course of this thread a photo of Greatr Northern gondola #72600 was submitted. This caught my attention as I had bought this kit from sunshine many years ago. I backed down from building it while I pondered how to do the tie down loops on the sides of the car (this was not in the
toggle quoted messageShow quoted text
Sunshine instructions0). The photo brings the car back into my list of priorities or if someone has the SL-SF stock car mentioned last week I would be willing to trade. Bill Pardie
|
|
|
|
Re: MEK Substitute and current plastic cements
Gary Ray
What are you wanting to know from a chemist? I’m currently visiting my daughter who has a degree in organic chemistry. Gary Ray
From: main@RealSTMFC.groups.io [mailto:main@RealSTMFC.groups.io] On Behalf Of Jon Miller
Sent: Tuesday, August 20, 2019 9:14 AM To: main@RealSTMFC.groups.io Subject: Re: [RealSTMFC] MEK Substitute and current plastic cements
On 8/20/2019 7:01 AM, Pierre Oliver wrote: MEK is used by the pint for plexiglas joinery I've never had any luck using MEK to join Plexiglas. I use a acrylics cement from TAP plastic. The can says Dichloromethane contains; Methylene chloride Anyone know a chemist?:-D
-- Jon Miller For me time stopped in 1941 Digitrax Chief/Zephyr systems, SPROG, JMRI User NMRA Life member #2623 Member SFRH&MS
|
|
|
