Charlie,

This is an interesting alternative, although it only works for 35mm slides. It came up on the RR Historical Society SIG group. Credit to Jeff Eggert over at CNWHS:

http://www.yardoffice.com/archives/howto/slideshootingdslr.html

In addition to being pretty fast, if you already have a slide projector and DLSR, it is of nominal cost.

At some point I need to use this setup for my non-RR family slide collection. I used a Canon film scanner in the past, and liked it very much, but it has suffered a hardware failure after about 15 years and I have not yet attempted a repair (nor do I know if parts are available.)

But my Canon scanner could never scan close to the 300 slides per hour rate that Jeff claims.

Dave Evans

On Nov 21, 2020, at 12:02 PM, Chuck Cover <chuck.cover@...> wrote:

Hi Eric,

 

I wanted to get back to you to thank you again for the help you provided on the Accurail 1800 series boxcar kitbash.  I went with the DL&W 36’ car partly because of the information that you sent me and because I have a DL&W interchange on my layout so DL&W cars fit in nicely.

 

I have attached a couple of photos.  I shaved off all of the cast on grabs and other details, followed your notes for your kitbash of the DL&W boxcar and added carver cut levers and end of car air hoses as well as AB brakes since I model the mid-50s and K4 decals.  I had not used the K4 decals before and thought that they were great.  Not sure if the Andrews trucks are correct, any suggestions?

 

Thanks again and take care,

 

Chuck

 

 

From: main@RealSTMFC.groups.io <main@RealSTMFC.groups.io> On Behalf Of Eric Hansmann
Sent: Saturday, October 31, 2020 2:46 PM
To: main@RealSTMFC.groups.io
Subject: Re: [RealSTMFC] Accurail 1800 series bocxcar kitbash

 

A few railroads used ends similar to the indestructible design to upgrade older cars. They turn up on wood sheathed B&O, DL&W, and Erie boxcars. 

 

It was determined awhile back by a couple B&O modelers that the ends used on B&O cars were home built and had differences to the ends used on D&H, DL&W, and Erie cars. IIRC, one major difference is the angled pieces point a different way on the B&O cars. 

 

This end view of an Erie boxcar shows the design, but the components don’t seem a heavy as what was used on B&O cars.

http://hansmanns.org/images/canton_industry_2.JPG

 

Compare the Erie car end with the B&O car in the attachment.

 

 

Eric Hansmann

Murfreesboro, TN

 

 

 

 

From: main@RealSTMFC.groups.io <main@RealSTMFC.groups.io> On Behalf Of Chuck Cover
Sent: Saturday, October 31, 2020 12:44 PM
To: main@RealSTMFC.groups.io
Subject: [RealSTMFC] Accurail 1800 series bocxcar kitbash

 

Group,

I was looking at Ray Breyer's discussion of the Accurail 1800 series boxcar and kitbash posiblities for the D&H 36' DS boxcar.  I would like to find more information on the "indestructible end" and the inverse Hutchins end.  I know that Funaro has models with the inverse Hutchins ends so they may be a source if they sell the ends separately.  Are there any other possible sources for this end?

Are there any drawings or articles which I can reference to bash the "indestructible ends"?  

Thanks,

Chuck Cover
Santa Fe, NM 

<IMG_0245.JPG><IMG_0246.JPG>

A few railroads used ends similar to the indestructible design to upgrade older cars. They turn up on wood sheathed B&O, DL&W, and Erie boxcars.

It was determined awhile back by a couple B&O modelers that the ends used on B&O cars were home built and had differences to the ends used on D&H, DL&W, and Erie cars. IIRC, one major difference is the angled pieces point a different way on the B&O cars.

This end view of an Erie boxcar shows the design, but the components don’t seem a heavy as what was used on B&O cars.

http://hansmanns.org/images/canton_industry_2.JPG

Compare the Erie car end with the B&O car in the attachment.

Eric Hansmann

Murfreesboro, TN

Group,

I was looking at Ray Breyer's discussion of the Accurail 1800 series boxcar and kitbash posiblities for the D&H 36' DS boxcar.  I would like to find more information on the "indestructible end" and the inverse Hutchins end.  I know that Funaro has models with the inverse Hutchins ends so they may be a source if they sell the ends separately.  Are there any other possible sources for this end?

Are there any drawings or articles which I can reference to bash the "indestructible ends"? 

Thanks,

Chuck Cover
Santa Fe, NM

----- Original Message -----

From: Schuyler Larrabee via groups.io

To: main@RealSTMFC.groups.io

Sent: Saturday, November 21, 2020 1:24 PM

Subject: Re: [RealSTMFC] Photo: NP Automobile Boxcar 6181 (1934)

Better than that, I saved a copy of the expanded image and zoomed in on that.  I >CAN< see some indication of joints but it simply was not “for sure” for me.

 

Thanks to the respondents for the clarity.

 

Schuyler

 

 

 

From: main@RealSTMFC.groups.io <main@RealSTMFC.groups.io> On Behalf Of Robert kirkham
Sent: Saturday, November 21, 2020 1:21 PM
To: main@RealSTMFC.groups.io
Subject: Re: [RealSTMFC] Photo: NP Automobile Boxcar 6181 (1934)

 

Did you click on the expand icon before zooming?  When I do that I can see the cracks between the individual boards.  Here’s a snippet:

 

Rob 

 

On Nov 21, 2020, at 10:12 AM, Schuyler Larrabee via groups.io <schuyler.larrabee@...> wrote:

 

Even though I’ve zoomed in quite a ways, could someone confirm my impression that this is a wood-sheathed car?

 

The door’s wood, but I am not completely sure that the car side is wood.

 

Schuyler

 

From: main@RealSTMFC.groups.io <main@RealSTMFC.groups.io> On Behalf Of Bob Chaparro via groups.io
Sent: Saturday, November 21, 2020 11:52 AM
To: main@RealSTMFC.groups.io
Subject: [RealSTMFC] Photo: NP Automobile Boxcar 6181 (1934)

 

Photo: NP Automobile Boxcar 6181 (1934)

A photo from the Denver Public Library:

https://digital.denverlibrary.org/digital/collection/p15330coll22/id/57922/rec/104

Click on the arrows in the upper right hand corner of the photo to enlarge it and scroll to enlarge it further.

Car built in 1923.

The car's reporting marks are repeated on the right end.

Although not legible, there is a car inspection card above the right wheel of the left truck. 

Bob Chaparro

Hemet, CA

 

Did you click on the expand icon before zooming?  When I do that I can see the cracks between the individual boards.  Here’s a snippet:

On 21 Nov 2020, at 18:12, Schuyler Larrabee via groups.io <schuyler.larrabee@...> wrote:



Even though I’ve zoomed in quite a ways, could someone confirm my impression that this is a wood-sheathed car?

 

The door’s wood, but I am not completely sure that the car side is wood.

 

Schuyler

 

From: main@RealSTMFC.groups.io <main@RealSTMFC.groups.io> On Behalf Of Bob Chaparro via groups.io
Sent: Saturday, November 21, 2020 11:52 AM
To: main@RealSTMFC.groups.io
Subject: [RealSTMFC] Photo: NP Automobile Boxcar 6181 (1934)

 

Photo: NP Automobile Boxcar 6181 (1934)

A photo from the Denver Public Library:

https://digital.denverlibrary.org/digital/collection/p15330coll22/id/57922/rec/104

Click on the arrows in the upper right hand corner of the photo to enlarge it and scroll to enlarge it further.

Car built in 1923.

The car's reporting marks are repeated on the right end.

Although not legible, there is a car inspection card above the right wheel of the left truck.

Bob Chaparro

Hemet, CA