In addition to Eds' information the following is from one of our diagram books. The page for this car has been copied a zillion times so some of the road numbers are hard to read. Also note the

List, After yesterday's thread on the DA tank car dome and its uses, I went home and dug out the partial diagrams I have for three classes of Southern Pacific tank cars, one of which (O-50-13) can be

Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the STMFC group. File : /P1010018.jpg Uploaded by : losgatos48

Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the STMFC group. File : /final%20b%20end.jpg Uploaded by : losgatos48

This is the address to see a fantastic rivet embossing machine. http://www.galtran.com/PRR_L2_Construction_Information/Rivet%20Machine/computer_controlled_rivet_emboss.htm Marcelo Lordeiro

Brian, please make them available without wheels... It isn't just a matter of cost. I have no use at all for .110 wheel sets anymore. (I have a lifetime supply of them as they come with most kits.)

Ooooo, an outdated standard rears its ugly head again. Brian, could I convince you to adopt the "Athearn standard" .295" centerplate height that almost everyone in the industry other than Kadee and

Her's a source for the drill: http://www1.mscdirect.com/CGI/NNSRIT?PMPXNO=1686302&PMT4NO=2590521 I also might note that Creative Model Associates (Tichy) has .008 diameter phosphor bronze wire,

with Barber Lateral Motion device detail and without. These trucks will be Celcon (similar to metal .110" wheelsets. Bolster height will match NMRA's RP 23 (5/16"). Naperville, before tooling was

Gene, Thanks for the offer, but I don't want to take orders until the trucks are ready to ship. They'll be available direct and from dealers ( lots of dealers, I hope). Brian Leppert Tahoe Model

This is what is written on that site: NOTES FROM OUR TECH DEPARTMENT This is a 5"x9" Template with Five Scales of Shapes and Rivet Placement Lines. FEATURES: Makes perfect panel lines, fuel caps,

Thanks! Great scans!

I see... so what is the template made of? It must be very flexible, but also totally resistant to adhesives, and very very thin (.010?) Is that true? If so, I could tape down the template, and glue

Mark Heiden wants to know the following: Rock Island 27350-27849, 500 40ft PS-1 boxcars, built 1963. A prototype photo of RI 27560 is at: http://www.rr-fallenflags.org/ri/ri27560.jpg I'd like to

Tim, The goal here is to space the rivet_s_ evenly. A common problem with airplanes and railroad equipment. Was that your question? It is not about application of singles. But that makes me think:

Tim; I started one, but got disheartened when I tried to paste on those alternating rivets where the interior tank heads were located. Too difficult for me. I wish I had the talent. There are

Mark Heiden has a question about a car that is out of our time period. I'm going to permit it's entry into discussion but only with regard to this one car series and discussion will not be allowed to

Hello Garth, The 50 foot PS-1 with 8 foot door opening is, more or less, still on our "possible" future project list, which changes all the time. Doing this car would require a new body and

I photographed that tank car at Steamtown in August 1997 and have just uploaded six scans to the STMFPH <Files> section. They are in a folder titled "NATX 4753 Tank Car". The

Kevin; Thanks for that great scan! Tom; I agree with Bruce, and Kevin's scan indicates it is almost certainly an early GATC product, and the bolsters, tank supports, angled draft gear support