Date   

Re: SP A-50-10 Fifty Foot, OB end door Boxcar

gary laakso
 

I have the HO Oriental Models import of this car and 2 questions: 1) were the end doors lined in wood and 2) what decals should be used?


gary laakso
south of mike brock
vasa0vasa@earthlink.net


Re: NYC Steel Boxcars, New Models?

ljack70117@...
 

This gentleman is 100% correct. No wonder these plastic models are being done with all the wrong measurement in them.
Thank you
Larry Jackman
Boca Raton FL
ljack70117@adelphia.net
I was born with nothing and
I have most of it left

On Apr 16, 2007, at 2:19 PM, Charlie Vlk wrote:

Tom-
I don't think that 3D Cad images are a substitute for preproduction samples or pilot models.
They do allow the proofing of design concepts and go a long way in catching any proportion issues before committing to tooling.
I am afraid, however, that some builders think that looking at a general arrangement 2D projection of the 3D file and a few selected
3D jpegs is enough for an importer to make final approval for production.
If it were MY money on the line I would insist on being able to view the full 3D file on my own computer to verify all details and dimensions of all
components prior to authorizing tooling. Test shots or (in the case of Brass) are still necessary to check out final fit and finish issues
prior to production. Fully decorated shells, at least for each paint job, are also necessary as final paint and printing colors, alignment
issues, etc.. are very hard and expensive to get corrected after production has started.
Charlie Vlk
Railroad Model Resources


No, providing a viewable SolidWorks (or other 3D CAD file) image in
lieu of an physical model is now a legitimate, advanced design
practice.

Tom Madden
.






Yahoo! Groups Links



Re: GN 12 panel take 3

leakinmywaders
 

--- In STMFC@yahoogroups.com, Anthony Thompson <thompson@...> wrote:

I wrote
The two SP prototype classes of 12-panel box cars DID have the thin
top stiffener. I hope IM did not remove that stiffener in order to
model the SP cars <g>.
Tim O'Connor replied:
Tony, this one doesn't.

http://www.speedwitch.com/Images/models/sp21622.jpg
Perhaps we are descending into the Swamp of Definitions.....

Hey, I am just relieved to find out I am not the only one confused by
this conversation! I'm in good company this time...;-)

Chris Frissell
Polson, MT
(*sitting here wondering there the GN-built SP&S 12-panels fit in,
having heard at least two conflicting accounts on their ends from
other sources...but perhaps now is not quite time to ask*)


Looking for an HO Overland WABASH Auto Boxcar

ogdentowebercanyon
 

I am looking for an Overland Models WABASH sheathed Automobile boxcar
that they did. If you have one you can part with or know of a store
that does, please let me know off-list. Thanks.

Jason Sanford


Re: X29 Pants (!) on eBay

Tim O'Connor
 

Nope, cuff-lers.

At 4/17/2007 12:18 AM Tuesday, you wrote:
But do the pants come with patch panels?

Al Brown, Melbourne, Fla.


--- In STMFC@yahoogroups.com, Brian Paul Ehni <behni@...> wrote:

Just refine your search with a ³-cute²! 8^)
--
Thanks!

Brian Ehni



From: Dennis Storzek <destorzek@...>
Reply-To: <STMFC@yahoogroups.com>
Date: Mon, 16 Apr 2007 22:33:21 -0000
To: <STMFC@yahoogroups.com>
Subject: [STMFC] Re: X29 Pants (!) on eBay





--- In STMFC@yahoogroups.com <mailto:STMFC%40yahoogroups.com> ,
"pullmanboss" <tgmadden@> wrote:

I've been watching a Red Caboose L&NE X29 kit on eBay. The "ending
soon" email notice just arrived and, as always, it includes a
listing
of "Similar Items on eBay". There are five various RC X29's on the
list, plus a red caboose from Atlas and another from Marx. Plus
one "ST. JOHNS BAY KHAKI PANTS SIZE 22W (40X29)". I did a
quick "what
the..." before I saw that "X29" nested in the description.

So, if any of you SPFs want some freight car pants, eBay's got a
pair
for you! Or go after the L&NE kit - I'm waiting for Ted's version.

Tom Madden
Tom,

You should try searching for models and memorabilia for the Soo
Line.
You'll never believe the number of different things people think are
"soo cute" :-(

Dennis




Yahoo! Groups Links



Re: X29 Pants (!) on eBay

al_brown03
 

But do the pants come with patch panels?

Al Brown, Melbourne, Fla.


--- In STMFC@yahoogroups.com, Brian Paul Ehni <behni@...> wrote:

Just refine your search with a ³-cute²! 8^)
--
Thanks!

Brian Ehni



From: Dennis Storzek <destorzek@...>
Reply-To: <STMFC@yahoogroups.com>
Date: Mon, 16 Apr 2007 22:33:21 -0000
To: <STMFC@yahoogroups.com>
Subject: [STMFC] Re: X29 Pants (!) on eBay





--- In STMFC@yahoogroups.com <mailto:STMFC%40yahoogroups.com> ,
"pullmanboss" <tgmadden@> wrote:

I've been watching a Red Caboose L&NE X29 kit on eBay. The "ending
soon" email notice just arrived and, as always, it includes a
listing
of "Similar Items on eBay". There are five various RC X29's on the
list, plus a red caboose from Atlas and another from Marx. Plus
one "ST. JOHNS BAY KHAKI PANTS SIZE 22W (40X29)". I did a
quick "what
the..." before I saw that "X29" nested in the description.

So, if any of you SPFs want some freight car pants, eBay's got a
pair
for you! Or go after the L&NE kit - I'm waiting for Ted's version.

Tom Madden
Tom,

You should try searching for models and memorabilia for the Soo
Line.
You'll never believe the number of different things people think are
"soo cute" :-(

Dennis


Re: Resin prepping

Walter M. Clark
 

Paul, and everyone,

It may be (probably is) a case of God takes care of fools but when I
started building resin kits about a dozen years ago I never even
thought about washing them before assembly. While I would like to
change some of the lettering on those first few, courtesy of what I've
learned here, none of the parts have even started to look or feel a
little loose. The one thing I did different to anything else I've
seen here was mix a little five minute epoxy to anchor the running
boards. My thumb-fingered lack of coordination coupled with inherited
essential tremor makes it impossible for me to get those things to
hold still while I apply that tiniest bit of ACC.

Walter M. Clark
Time stopped in November 1941
Riverside, California

--- In STMFC@yahoogroups.com, cobrapsl@... wrote:

Bruce,

I totally agree with you that there is no need to spend money on
"resin prep" voodoo mixtures. I personally like something a little
stronger than dish detergent for the initial pre-assemble "scrub", but
it will certainly work. If using dish detergent, I caution those
following this tread that it needs to be one of the ones with no added
oils like original Dawn. Dawn is what I use as the final wash prior to
painting.

Bruce, I did not mean to be critical of yours and Jim's approach,
just I think it is best to teach folks how to drive with both hands on
the steering wheel--they will find what is comfortable to them soon
enough!

Paul Lyons
Laguna NIguel, CA



-----Original Message-----
From: smithbf@...
To: STMFC@yahoogroups.com
Sent: Sun, 15 Apr 2007 5:38 AM
Subject: Re: [STMFC] Resin prepping


On Sat, April 14, 2007 10:00 pm, cobrapsl@... wrote:
Jim, Bruce,

I understand sanding the "flat pieces" first and dressing the
edges to be
glued with a file. All of us experienced builders do those
assembly steps,
but that is only a small part of putting a resin kit together. If
you are
not cleaning the mould release agent off, what are you doing to
assure a
good bond of the surfaced applied parts, i.e. ladders, handbrake
housings.
brake step platform supports, etc?
Paul, et al.,

Maybe ACC works differently here? (I say that only slightly in jest,
given
that humidity is a critical component for ACC and Paul lives in
California
and I in Alabama, where I have no doubt that the relative humidities
differ more than slighly). I really have no problem with ladders etc.
When things start to fail to stick, I find that it is time for a
bottle of
fresh ACC.

I guess I would agree that washing parts beforehand, especially for
a new
kit builder, certainly isn't going to hurt anything (if you're careful
<G>) and may help. However, I would also say that there is no reason to
go out and spend money on "resin prep" voodoo when simple dish detergent
will work just fine ;^)

Regards
Bruce

Bruce Smith
Auburn, Al (currently very wet, but NOT snowy!)



________________________________________________________________________
AOL now offers free email to everyone. Find out more about what's
free from AOL at AOL.com.


[Non-text portions of this message have been removed]


Re: Roof Corner Hand Rail Bending

Lawrence Rast
 

Thanks for the response, Andy.

Perhaps this weekend I'll give this a shot and put together some pics for
the internet. That is, if the "honey do" list isn't too long...

Best,
Lawrence Rast

On 4/16/07, Andy Sperandeo <asperandeo@mrmag.com> wrote:

Hi Lawrence,

Sorry. I'm pretty sure I've never written about this for MR, but it's
possible that I learned how to do this from some scratchbuilding storu
from
the distant past.

So long,

Andy

Andy Sperandeo
Executive Editor
Model Railroader magazine
asperandeo@mrmag.com <asperandeo%40mrmag.com>
262-796-8776, ext. 461
FAX 262-796-1142






Re: T&NO triple offset-side hopper car shipments

Anthony Thompson <thompson@...>
 

The triple offset side T&NO hopper cars I saw were loaded with
limestone/dolomite aggregate at Beckmann, Texas on the old SA&AP branch
to Kerrville. The quarry was called McDonough Brothers (sp?) during
the steam era. The aggregate was NOT used for cement, it was
construction aggregate for the Houston area - for roads and building
foundations. Some may also have been used for ballast on the railroad
during the 1940's. Loads went over the GH&SA from San Antonio to
Houston (I do not know where in Houston it was unloaded).
Thanks for the great info! Just what I needed, and it fits with the approximate size of the rock being loaded into cars.

Tony Thompson Editor, Signature Press, Berkeley, CA
2906 Forest Ave., Berkeley, CA 94705 www.signaturepress.com
(510) 540-6538; fax, (510) 540-1937; e-mail, thompson@signaturepress.com
Publishers of books on railroad history


T&NO triple offset-side hopper car shipments

proto48er
 

Tony -

The triple offset side T&NO hopper cars I saw were loaded with
limestone/dolomite aggregate at Beckmann, Texas on the old SA&AP branch
to Kerrville. The quarry was called McDonough Brothers (sp?) during
the steam era. The aggregate was NOT used for cement, it was
construction aggregate for the Houston area - for roads and building
foundations. Some may also have been used for ballast on the railroad
during the 1940's. Loads went over the GH&SA from San Antonio to
Houston (I do not know where in Houston it was unloaded). Sand from
Gemmer & Tanner in the Columbus, Texas area and oyster shell from
Galveston Bay were previously/concurrently used as aggregate, but the
limestone was apparently superior. The traffic continues to this day
from the same quarry.

A.T. Kott


Re: GN 12 panel take 3

Tim O'Connor
 

[ Take Four ]

Tony Thompson wrote

The contrast, if I understood the discussion correctly, had to do with
whether there was ANY small rib above the highest major corrugation.
Not my understanding. The small stiffener was well above the major
and minor corrugations, and is clearly present on most GN cars and
the SP B-50-27/28 classes, and absent from the B-50-25/26 and some
GN cars... as we have discussed up to this point.

But as Ed pointed out clearly, no one (including Sunshine) makes the
end with the small stiffener correctly, because the topmost major "rib"
(corrugation) has a flattened bottom edge.

Intermountain's end without the stiffener (which I believe is the second
or later version in the IRC timeline) is the only correct end for SP 12 panel
cars, some GN 12 panel cars, and is incorrect for SP 10 panel cars.

Tim


Re: GN 12 panel take 2

Martin McGuirk <mjmcguirk@...>
 

My bad -- the Overnight cars weren't 12-panels -- I think we used a
different end on them so it would have the top riblet -- that also
gave it the holes for the horizontal bar grab.

All these things have blended together -- the "original" paint scheme
on the GN 12-panels included the horizaontal bar -- which is correct
for the car in later years, but not in the original dark BCR paint.

Marty

On Apr 16, 2007, at 5:01 PM, Anthony Thompson wrote:

Marty McGuirk wrote:
It is possible that IRC cut a new end since I left, but I kind of
doubt it . . . I know the end with the horizontal grab was, at one
point, the only one that fit the 12-panel -- which is why that
end is
used with things like SP and ATSF 12-panel cars --- we left it
off the
SP Overnight cars done for Yesteryear by using the Modified AAR end,
but if I recall the alignment holes had to be adjusted.
You mean the Yesteryear Overnight model was done with the
12-panel body? (urk)

Tony Thompson Editor, Signature Press, Berkeley, CA
2906 Forest Ave., Berkeley, CA 94705 www.signaturepress.com
(510) 540-6538; fax, (510) 540-1937; e-mail,
thompson@signaturepress.com
Publishers of books on railroad history



GN 12 panel take 3

Anthony Thompson <thompson@...>
 

I wrote
The two SP prototype classes of 12-panel box cars DID have the thin top stiffener. I hope IM did not remove that stiffener in order to model the SP cars <g>.
Tim O'Connor replied:
Tony, this one doesn't.

http://www.speedwitch.com/Images/models/sp21622.jpg
Perhaps we are descending into the Swamp of Definitions. I would agree that the some of the P-S cars built for SP have more of a thin, straight rib, instead of a tapered thin rib like those between the major corrugations. (Let's not call it a "riblet" lest I think excessively of BBQ.) See the relevant pages in my SP Freight Cars Vol. 4 for additional photos. The contrast, if I understood the discussion correctly, had to do with whether there was ANY small rib above the highest major corrugation.

Tony Thompson Editor, Signature Press, Berkeley, CA
2906 Forest Ave., Berkeley, CA 94705 www.signaturepress.com
(510) 540-6538; fax, (510) 540-1937; e-mail, thompson@signaturepress.com
Publishers of books on railroad history


Re: X29 Pants (!) on eBay

Brian Paul Ehni <behni@...>
 

Just refine your search with a ³-cute²! 8^)
--
Thanks!

Brian Ehni



From: Dennis Storzek <destorzek@mchsi.com>
Reply-To: <STMFC@yahoogroups.com>
Date: Mon, 16 Apr 2007 22:33:21 -0000
To: <STMFC@yahoogroups.com>
Subject: [STMFC] Re: X29 Pants (!) on eBay





--- In STMFC@yahoogroups.com <mailto:STMFC%40yahoogroups.com> ,
"pullmanboss" <tgmadden@...> wrote:

I've been watching a Red Caboose L&NE X29 kit on eBay. The "ending
soon" email notice just arrived and, as always, it includes a listing
of "Similar Items on eBay". There are five various RC X29's on the
list, plus a red caboose from Atlas and another from Marx. Plus
one "ST. JOHNS BAY KHAKI PANTS SIZE 22W (40X29)". I did a quick "what
the..." before I saw that "X29" nested in the description.

So, if any of you SPFs want some freight car pants, eBay's got a pair
for you! Or go after the L&NE kit - I'm waiting for Ted's version.

Tom Madden
Tom,

You should try searching for models and memorabilia for the Soo Line.
You'll never believe the number of different things people think are
"soo cute" :-(

Dennis


Re: GN 12-panel boxcars

Barry Roth
 

At least some of the Intermountain SP 12-panel cars (including two assembled ones I bought) have the slender top riblet. I have no idea whether these were from an early or a late run of the product, or how one would know, without examining an individual specimen, whether any given car or kit had the stamping.

Barry Roth

"Steve Haas (G2)" <Goatfisher2@comcast.net> wrote:
Since I started the latest round of this discussion I guess I better
contribute a few facts.

This is extracted from a table I've worked on from time to time.

GN 10' 12 Panel Cars

Series Start: 2525
Series End: 2549
Built: 1948
Doors: Seven Panel
Ends: 4/3/0

Series Start: 10900
Series End: 11374
Built: 1948
Doors: Seven Panel & 4-6-6
Ends: 4/3/0

The above two series can be built from the Intermountain 41001 series by
sanding off the thin top stamping, or by substituting the end from the 41013
series (SP 12 panel) or the 41099 (undec). As Ed, Tim, and Andy have been
discussing, the ends from these latter Intermountain models lack the thin
top stamping. [...]


.





---------------------------------
Ahhh...imagining that irresistible "new car" smell?
Check outnew cars at Yahoo! Autos.


Re: X29 Pants (!) on eBay

Dennis Storzek
 

--- In STMFC@yahoogroups.com, "pullmanboss" <tgmadden@...> wrote:

I've been watching a Red Caboose L&NE X29 kit on eBay. The "ending
soon" email notice just arrived and, as always, it includes a listing
of "Similar Items on eBay". There are five various RC X29's on the
list, plus a red caboose from Atlas and another from Marx. Plus
one "ST. JOHNS BAY KHAKI PANTS SIZE 22W (40X29)". I did a quick "what
the..." before I saw that "X29" nested in the description.

So, if any of you SPFs want some freight car pants, eBay's got a pair
for you! Or go after the L&NE kit - I'm waiting for Ted's version.

Tom Madden

Tom,

You should try searching for models and memorabilia for the Soo Line.
You'll never believe the number of different things people think are
"soo cute" :-(

Dennis


X29 Pants (!) on eBay

pullmanboss <tgmadden@...>
 

I've been watching a Red Caboose L&NE X29 kit on eBay. The "ending
soon" email notice just arrived and, as always, it includes a listing
of "Similar Items on eBay". There are five various RC X29's on the
list, plus a red caboose from Atlas and another from Marx. Plus
one "ST. JOHNS BAY KHAKI PANTS SIZE 22W (40X29)". I did a quick "what
the..." before I saw that "X29" nested in the description.

So, if any of you SPFs want some freight car pants, eBay's got a pair
for you! Or go after the L&NE kit - I'm waiting for Ted's version.

Tom Madden


Looking for Red Caboose Wood Interiors for X-29 and AAR Boxcars

ogdentowebercanyon
 

I am looking for some of the Red Caboose peel and stick boxcar
interiors for the 1937 AAR boxcar both single and double door and I am
also looking for the X29 interior. If you have some that you can part
with, please let me know and it will be greatly appreciated.

Jason Sanford

P.S. Can't find them online including walthers. Red Caboose seems to
be low on supply they say.


Re: NP 1912-1918 truss rod box cars

Dennis Storzek
 

--- In STMFC@yahoogroups.com, timboconnor@... wrote:

Thanks for that link Dennis....

Tim "confused as ever" O'Connor

It gets worse, Tim. I just clicked on the link to make sure it worked,
and realized the photo array is one of those "which item doesn't
belong with the rest" tests. Either that, or the car has three ends.
The NP car has end posts that protrude through the end sheathing on
both ends, a construction detail that was intended to provide the
strongest possible post without making the end any thicker than
necessary. The end with the ladder, rather than grab irons, is from a
different car, likely one of the URTX reefers.

I would take the NP 49444 number with a grain of salt; it may have
been determined from faint stenciling remaining on the car, and
possibly mis-read. 40444 would fall within the series you noted.

Dennis


Re: GN 12 panel take 2

Tim O'Connor
 

Anthony Thompson <thompson@signaturepress.com> wrote

The two SP prototype classes of 12-panel box cars DID have the
thin top stiffener. I hope IM did not remove that stiffener in order to
model the SP cars <g>.
-----------------------------------

Tony, this one doesn't.

http://www.speedwitch.com/Images/models/sp21622.jpg

I think the 12 panel cars did NOT have the stiffener, but the later
B-50-27/28 (10 panel) cars did have the stiffener. But I'm at work
at the moment so this is going from memory...

Tim O'Connor

123341 - 123360 of 185166